Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.

Do not ignore the forklift at the workplace. If the procedure is not good, there will be major mishaps in minutes, and there are lots of mishaps entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead might not be discovered, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over throughout a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress (air pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the lots is steady and reliable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake instantly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain security distance from the car in front. .
7. When the forklift is running, the tons should remain in the lowest setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The elevation of the lots have to not obstruct the vehicle driver's view. In special situations, when the product affects the forward vision, drive at a low rate when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold products and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety and security indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll Electric Forklift Truck for Warehouse the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork Electric Forklift Truck for Warehouse the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other goods or items. The tons must be stabilized with marginal back tilt of the gantry to make sure that the tons does not glide in reverse. The mast can be slanted forward somewhat when the lots is lowered to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is banned to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the hand brake handle to dead or depress the emergency brake switch.
3. The engine is shut off and the power is removed. (Except for special situations, such as the chauffeur does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubing oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the procedure of the forklift, check whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the slope. When the gradient is more than 10%, the car must be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844